Description
NETWORK STATE TESTER
An All-rounder Fiber Network State Tester
ONT/ONU State Tester, GPON/EPON Power Meter
Visual Fault Locator, RJ45 Cable Sequence/Length/Tracking
ONT/ONU STATES
> ONLINE
> OFFLINE
> ONT FATAL
> ONT BAD
> ONT NO POWER
> FIBER FALL OFF
PON POWER METER
VISUAL FAULT LOCATOR
RJ45 Cable Sequence
Longueur du câble RJ45
RJ45 Cable Tracking
| Général | |
| Size/Weight | 173x82x37mm/ 350g |
| Afficher | 3.5 Inch TFT LCD, 320×480 Resolution |
| Interface | Micro USB |
| Alimentation | 5V DC, 2A; 4000mAh/3.7V Lithium battery (with air traffic certification) |
| Temps de travail | >12 heures (mesure continue) ; veille >20 heures |
| Langue | Chinese, English |
| Environmental Conditions | Operating temperature and humidity: -10℃~+50℃, ≤95% (non-condensation)Storage temperature and humidity: -40℃~+70℃, ≤95% (non-condensation) |
| Network State Tester | |
| ONT States | Online, Offline, ONT Fatal, ONT Bad, ONT No Power, Fiber Fall Off |
| Insertion Loss | <1.5dB |
| Connector | FC/SC/ST |
| PON Power Meter | |
| Plage d'essai | -35 to +10dBm @1310nm (upstream)-40 to +12dBm @1450nm (Downstream)-40 to +25dBm @1550nm (Downstream) |
| Unité | mW/uW/nW/dBm/dB (REF) |
| Précision | 0.5dB |
| Resolution | 0,01 dB |
| Localisateur visuel de défauts | |
| Longueur d'onde | 650 nm |
| Puissance de sortie | 10 mW, CLASSE III B |
| Gamme | 12km |
| Launching Mode | CW/1 Hz/2 Hz |
| Type d'adaptateur | Adaptateur universel 2,5 mm pour connecteurs FC SC ST |
| Rj45 Cable Tracking | |
| Gamme | 300m |
| Type de signal | Signal analogique/signal numérique |
| Récepteur de signal | Optional |
| Son d'avertissement | Soutien |
| Cable Type | 568A, 568B |
| Rj45 Cable Sequeence | |
| Gamme | 300m |
| Type de signal | Analog Signal/Digital Signal |
| Test de câble actif | Non pris en charge |
| Temps d'essai | Less Than 15 Seconds |
| Unité distante | Peut être retiré par le bas de l'appareil |
| Rj45 Cable Length | |
| Gamme | 300m |
| Type de signal | Signal analogique/signal numérique |
| Test de câble actif | Non pris en charge |
| Temps d'essai | Less than 15 seconds |
Why the tester is needed?
With the popularity of PON network and the blowout development of optical network terminals, telecom operators need to have a new method to check the occupation of resources on optical ports to reduce the waste of port resources.
By a kind of traditional manual checking is extremely complicated, inefficient, and will bring huge trouble to subscribers.
The PON terminal state tester can intelligently check the resource state of optical network terminal and intelligently analyze the ONT and PON network without maintenance personnel entering the subsriber’s house.
It is integrated with PON optical power meter, visual fault location, RJ45 cable sequence/length and digital cable tracker. The tester is an all-round helper in the field of current PON network maintenance and terminal resource checking
Télécharger
FAQ
How many testing results the device can save?
1000 test results can be saved in the device. When reach 1000, the last result will be covered by a new testing result.
