Descrição
NETWORK STATE TESTER
An All-rounder Fiber Network State Tester
ONT/ONU State Tester, GPON/EPON Power Meter
Visual Fault Locator, RJ45 Cable Sequence/Length/Tracking
ONT/ONU STATES
> ONLINE
> OFFLINE
> ONT FATAL
> ONT BAD
> ONT NO POWER
> FIBER FALL OFF
PON POWER METER
VISUAL FAULT LOCATOR
RJ45 Cable Sequence
Comprimento do cabo RJ45
RJ45 Cable Tracking
| Em geral | |
| Size/Weight | 173x82x37mm/ 350g |
| Mostrar | 3.5 Inch TFT LCD, 320×480 Resolution |
| Interface | Micro USB |
| Fonte de energia | 5V DC, 2A; 4000mAh/3.7V Lithium battery (with air traffic certification) |
| Horário de trabalho | >12 horas (Medição contínua); Em espera >20 horas |
| Linguagem | Chinese, English |
| Environmental Conditions | Operating temperature and humidity: -10℃~+50℃, ≤95% (non-condensation)Storage temperature and humidity: -40℃~+70℃, ≤95% (non-condensation) |
| Network State Tester | |
| ONT States | Online, Offline, ONT Fatal, ONT Bad, ONT No Power, Fiber Fall Off |
| Insertion Loss | <1.5dB |
| Connector | FC/SC/ST |
| PON Power Meter | |
| Área de Teste | -35 to +10dBm @1310nm (upstream)-40 to +12dBm @1450nm (Downstream)-40 to +25dBm @1550nm (Downstream) |
| Unidade | mW/uW/nW/dBm/dB (REF) |
| Precisão | 0.5dB |
| Resolution | 0,01 dB |
| Localizador visual de falhas | |
| Comprimento de onda | 650nm |
| Potência de saída | 10mw, CLASSE III B |
| Faixa | 12km |
| Launching Mode | CW/1Hz/2Hz |
| Tipo de adaptador | Adaptador universal de 2,5 mm para conectores FC, SC e ST. |
| Rj45 Cable Tracking | |
| Faixa | 300m |
| Tipo de sinal | Sinal analógico/Sinal digital |
| Receptor de sinal | Optional |
| Som de aviso | Apoiar |
| Cable Type | 568A, 568B |
| Rj45 Cable Sequeence | |
| Faixa | 300m |
| Tipo de sinal | Analog Signal/Digital Signal |
| Teste de cabo ativo | Não oferece suporte. |
| Hora do teste | Less Than 15 Seconds |
| Unidade remota | Pode ser retirado pela parte inferior do dispositivo. |
| Rj45 Cable Length | |
| Faixa | 300m |
| Tipo de sinal | Sinal analógico/Sinal digital |
| Teste de cabo ativo | Não oferece suporte. |
| Hora do teste | Less than 15 seconds |
Why the tester is needed?
With the popularity of PON network and the blowout development of optical network terminals, telecom operators need to have a new method to check the occupation of resources on optical ports to reduce the waste of port resources.
By a kind of traditional manual checking is extremely complicated, inefficient, and will bring huge trouble to subscribers.
The PON terminal state tester can intelligently check the resource state of optical network terminal and intelligently analyze the ONT and PON network without maintenance personnel entering the subsriber’s house.
It is integrated with PON optical power meter, visual fault location, RJ45 cable sequence/length and digital cable tracker. The tester is an all-round helper in the field of current PON network maintenance and terminal resource checking
Download
FAQ
How many testing results the device can save?
1000 test results can be saved in the device. When reach 1000, the last result will be covered by a new testing result.
